Nationwide · Licensed electricians in 47 states + DC
Call now to check electrician availability in your area
Electrical Panel Upgrade · California
A panel upgrade replaces your breaker panel, and often the service entrance, so the home can safely carry more load: an EV charger, heat pump, induction range or addition. It always needs a permit, and usually needs the utility to disconnect and reconnect power.
Electrification, rooftop solar and EV adoption make panel upgrades common, and wildfire-season power shutoffs drive generator and battery hookups.
Across the Pacific, homes deal with mild coast, wildfire seasons inland, and wet winters in the Northwest. Permit offices, utilities and housing stock differ by city, which affects how electrical panel upgrade is planned and scheduled. These local guides cover the California cities where we have written specific notes.
Electrification drives most panel upgrades in Los Angeles. A 1920s craftsman or a 1950s tract house with a 60 or 100 amp service often cannot support an EV charger, a heat pump, an induction range and rooftop solar together.
Utility: LADWP (city of Los Angeles)
San Diego has one of the highest rates of rooftop solar in the country, and a panel's bus rating often limits how much solar can be connected without an upgrade or main-breaker derate. Adding a battery, an EV charger or a heat pump to a 1950s Clairemont tract home or a North Park craftsman with a 100 amp panel usually needs a closer look.
Utility: SDG&E
Older Sacramento homes in Land Park, East Sacramento and Curtis Park often have 60 or 100 amp services, and adding a heat pump, an EV charger or rooftop solar commonly means an upgrade. SMUD, the city's publicly owned utility, handles the meter and service drop and has its own process for service changes and solar interconnection.
Utility: SMUD (publicly owned)
San Francisco flats often have several small services fed from a meter bank, and electrification projects such as heat pumps, induction ranges and EV charging usually need more capacity than a 60 or 100 amp service can supply. Garages with tight clearances can limit where a new panel or meter can go.
Utility: PG&E (lines and meters); CleanPowerSF for most customers' supply
Electrification is the biggest driver of panel upgrades in San Jose: heat pumps, induction ranges, heat-pump water heaters, EV chargers and solar often all end up on a panel that dates to the original 1950s or 1960s build. Some older homes still have Zinsco or Federal Pacific panels that electricians commonly recommend replacing.
Utility: PG&E (lines and meters); San José Clean Energy for most customers' supply
In Fresno, panel upgrades usually start with the heat. A post-war tract home with a 100 amp panel may already be near its limit when the central air runs through a long July afternoon, and adding rooftop solar, a battery or an EV charger on top of that often means a new panel or service.
Utility: PG&E
In Bakersfield, many older homes in Westchester and Oleander-Sunset still have the 60 or 100 amp service they were built with, sized for a time before central air. Replacing an aging swamp cooler with refrigerated air, adding a pool, rooftop solar or an EV charger often pushes the panel past its limit.
Utility: PG&E
A 1920s bungalow in California Heights or a 1950s Los Altos tract house typically came with a 60 or 100 amp service, and Long Beach homeowners adding an EV charger, a heat pump, an induction range or rooftop solar often outgrow it. Southern California Edison handles the meter and solar interconnection, and the work is permitted by Long Beach Development Services, not by Los Angeles.
Utility: Southern California Edison
Electrification is the main driver of panel upgrades in Oakland. Older flatland homes often have 60 or 100 amp services that cannot carry a heat pump, induction range, heat-pump water heater and EV charger together.
Utility: PG&E (lines and meters); Ava Community Energy for most customers' supply
In Pasadena, the electric utility is city-owned Pasadena Water and Power, not Southern California Edison, so service upgrades, meters and solar interconnection go through PWP. Older craftsman homes often have 60 or 100 amp services that cannot support heat pumps, induction cooking, EV chargers and solar together.
Utility: Pasadena Water and Power (city-owned)
1. Load calculation
The electrician sizes the service from your existing and planned loads.
2. Permit and utility coordination
The permit is pulled and the utility schedules disconnect and reconnect.
3. Install the panel and service parts
New panel, breakers, grounding and bonding, and service conductors or meter base if needed.
4. Inspection
The local inspector checks the work before or after power is restored, depending on the jurisdiction.
Electricians set their own prices; local permit fees and utility requirements add to these factors.
Permits come from the city or county where the home is. For example: Los Angeles: In the City of Los Angeles, electrical permits are issued by LADBS. San Diego: Inside city limits, electrical permits come from the City of San Diego Development Services Department; other cities in the county and unincorporated areas have their own building departments. Sacramento: Inside city limits, electrical permits come from the City of Sacramento Community Development Department; unincorporated areas are permitted by Sacramento County, and suburbs such as Elk Grove run their own. San Francisco: Electrical permits in San Francisco are issued by the Department of Building Inspection (DBI), and work must be done by a California-licensed electrical contractor. San Jose: Electrical permits in San José come from the city's Planning, Building and Code Enforcement department; other cities in Santa Clara County run their own building departments. Fresno: Electrical permits in Fresno come from the city's Planning and Development Department; Clovis and unincorporated Fresno County issue their own. Bakersfield: Electrical permits inside city limits come from the City of Bakersfield's building division; unincorporated areas are permitted by Kern County. Long Beach: Long Beach is its own city with its own building department, and electrical permits come from Long Beach Development Services rather than the City or County of Los Angeles. Oakland: Electrical permits in Oakland come from the city's Planning and Building Department; California electrical contractors are licensed by the Contractors State License Board. Pasadena: Pasadena has its own building department, and electrical permits come from the city's Planning and Community Development Department; Altadena is unincorporated and permitted by Los Angeles County.
Los Angeles: LADWP (city of Los Angeles). San Diego: SDG&E. Sacramento: SMUD (publicly owned). San Francisco: PG&E (lines and meters); CleanPowerSF for most customers' supply. San Jose: PG&E (lines and meters); San José Clean Energy for most customers' supply. Fresno: PG&E. Bakersfield: PG&E. Long Beach: Southern California Edison. Oakland: PG&E (lines and meters); Ava Community Energy for most customers' supply. Pasadena: Pasadena Water and Power (city-owned).
If you have 100 amps or less and are adding an EV charger, heat pump or electric range, or your panel is a Federal Pacific, Zinsco or fuse box, ask an electrician for a load calculation.
Usually most of one working day, depending on the scope and how quickly the utility reconnects.
Yes, in essentially every US jurisdiction. The electrician pulls it and schedules the inspection.
Call now, or send a request and a licensed electrician who serves your ZIP code will contact you.
